Why does my Sony STR D665 say protect?

I have a Sony STR-D665 receiver, that states “protect” on the display about 2 seconds after turning it on, and it won’t do anything. Does anyone know how to fix this? It does it regardless of anything connected to it or not. That is usually caused by a short in one of the speakers.

How to fix Sony receiver ” protect ” mode?

Sony receiver “protect” mode? I have a Sony STR-D665 receiver, that states “protect” on the display about 2 seconds after turning it on, and it won’t do anything. Does anyone know how to fix this?

Is there a problem with my Sony receiver?

If there is a problem youll see a dead short between the leads. You might also want to put a ohm meter between the speaker output terminal and see if there is a difference between some of them. Just a shot in the dark but you never know and make sure you unplug the unit before you make your measurements.

Why does my Sony receiver keep the volume down?

Keep the volume Down. When it does, that one has the problem. That or an internal fuse/circuit breaker has switched.

Why does my Sony surround sound receiver flash protector?

My goodness the internet is great. I was about to throw out a Sony surround sound receiver I’ve had for years because it would flash “PROTECTOR” on the display after being on for a few seconds, and I’d tried everything I could think of (cleaning, making sure no bits of wire in speaker posts, leaving off for hours or days, etc.).

My goodness the internet is great. I was about to throw out a Sony surround sound receiver I’ve had for years because it would flash “PROTECTOR” on the display after being on for a few seconds, and I’d tried everything I could think of (cleaning, making sure no bits of wire in speaker posts, leaving off for hours or days, etc.).

What to do if your Sony receiver is in Protector mode?

It basically said open it up, clean out the dust, and then disconnect and reconnect every connector you can get your hands on. I’d already vacuumed out the inside (which wasn’t really dusty anyway), but proceeded to disconnect and reconnect every connector in there, and there’s a BUNCH.

What to do if your Sony receiver blinks?

If there is nothing connected at all, it may be an internal short which can only be fixed by sending it in for service. If it is within warranty period, they will fix it for free. You must log in or register to reply here.

How to fix Sony amplifier protect mode error?

How to Fix Sony Amplifier Protect Mode Error The STR-K740P protect error usually occurs in the form of “PROTECT” flashing on the display, and this article looks into how to fix this error and bring the amplifier out of this mode. The purpose of the protect error is to protect the amplifier components from damage should a short circuit occur.

Why does my Sony TV keep going into Protect Mode?

That is usually caused by a short in one of the speakers. Try disconnecting them one by one to see when (if) it does finally power up. Keep the volume Down. When it does, that one has the problem. That or an internal fuse/circuit breaker has switched.

Why is my str-k740p in protect mode?

The STR-K740P protect error usually occurs in the form of “PROTECT” flashing on the display, and this article looks into how to fix this error and bring the amplifier out of this mode. The purpose of the protect error is to protect the amplifier components from damage should a short circuit occur.

I have a Sony STR-D665 receiver, that states “protect” on the display about 2 seconds after turning it on, and it won’t do anything. Does anyone know how to fix this? It does it regardless of anything connected to it or not. That is usually caused by a short in one of the speakers.

Sony receiver “protect” mode? I have a Sony STR-D665 receiver, that states “protect” on the display about 2 seconds after turning it on, and it won’t do anything. Does anyone know how to fix this?

How to repair Sony str-de675 receiver amplifier?

USB activity while switched off. An error occurred while retrieving sharing information. Please try again later.

The STR-K740P protect error usually occurs in the form of “PROTECT” flashing on the display, and this article looks into how to fix this error and bring the amplifier out of this mode. The purpose of the protect error is to protect the amplifier components from damage should a short circuit occur.